An interceptor collects grease and solids before kitchen wastewater enters the sewer. As waste builds up, it can cover the outlet tee, restrict flow and make internal parts hard to check. Slow drains or standing water in the sink can mean the interceptor needs attention, though a blocked line can cause similar trouble. Cleaning addresses residue left on parts after waste removal. If an inspection is coming, past paperwork can help show what was done. Call a provider and describe the symptoms, the tank location and any upcoming inspection.
Call (877) 704-1271 to reach a provider →
How interceptors differ from indoor traps
An indoor grease trap is usually near the fixtures it serves. An interceptor is commonly a larger tank below grade outside the building, where it holds grease and solids from kitchen wastewater. Its location and access points change how cleaning is done.
If your past paperwork identifies an outdoor tank, ask about interceptor cleaning rather than assuming indoor trap service covers it. An interceptor may need waste removal plus cleaning around its inlet and outlet tees, baffles, and walls. Those parts are easier to check once buildup is cleared.
What thorough cleaning includes
- Open accessible lids and check the tank before waste removal begins.
- Remove floating grease, settled solids and wastewater from the interceptor.
- Clean residue from tank walls and accessible internal surfaces.
- Clear grease around inlet and outlet tees and baffles.
- Use jetting where appropriate to loosen buildup on accessible surfaces.
- Check the sample box, if present, for grease or settled material.
Ask what the work includes before it begins. Keep the service record, including any notes about damaged parts or areas that could not be cleaned.
Confined space considerations
An in-ground interceptor is an enclosed tank. Grease, wastewater and limited airflow can make entry hazardous, so cleaning is usually done from above through the access openings. Hoses and tools can reach into the tank without anyone climbing inside.
Access still matters. Buried lids, parked vehicles or stored supplies can prevent equipment from reaching an opening. Locate the lids and clear the surrounding area before service. If a section cannot be reached from above, ask what can be cleaned safely and what limitations should be documented.
Inspecting tees, baffles and lids
The inlet tee directs incoming flow, while the outlet tee helps keep floating grease from leaving the tank. Baffles separate areas inside the interceptor. Heavy buildup can hide cracks, loose fittings or missing pieces.
After cleaning, visible tees and baffles can be checked for damage and secure placement. A broken outlet tee may let grease move farther into the drain system. Ask for any damage found to be documented.
Lids deserve attention too. They should sit securely and remain accessible for future service. A cracked lid, damaged frame or opening that does not close properly is worth raising before the area is put back into use.
How buildup affects inspections
Thick grease can hide the condition of tees and baffles, making it harder to see whether the interceptor is working as intended. Waste near the outlet may also raise questions about what has been leaving the tank. Cleaning makes accessible parts easier to see.
Your city or sewer district sets its own service and recordkeeping requirements. Before an inspection, gather past paperwork and ask that the new record note the work performed and any damaged parts. Cleaning makes parts easier to assess, while the records help explain the interceptor's maintenance history.
What affects the price of interceptor cleaning
The tank's capacity, the amount of grease and solids inside, and access to its lids can affect the work involved. Cleaning residue from walls, tees and baffles may take different equipment than waste removal alone. Jetting or work at a sample box can also change the scope. Describe the interceptor's location, any blocked access and what the last cleaning covered. Ask which tasks are included in the price the provider discusses.
Grease interceptor cleaning questions
Is interceptor cleaning different from interceptor pumping?
Pumping removes the grease, solids and wastewater held in the tank. Cleaning can also address residue on accessible walls, tees and baffles. Ask the provider what work is included, especially if buildup is hiding internal parts or an inspection is coming.
How do I find my interceptor?
Check building plans or past paperwork for the tank location. Outside, look for access lids along the kitchen drain route, often between the building and the sewer connection. Avoid opening an unfamiliar lid yourself. If the location is unclear, describe the access lids and drain route to the provider.
What if parts inside are broken?
Ask the provider to note the damaged tee, baffle or lid on the service record and explain whether it affects the cleaning. Removing grease can make damage easier to see. A broken part may need separate repair; keep the written note for that follow-up.
Can cleaning happen while the kitchen is open?
That depends on where the access lids are and whether the work affects kitchen drains or areas used by staff and deliveries. Tell the provider about your operating hours and access needs. Ask whether drains can stay in use during cleaning.